Please fill out the contact form below and we will reply as soon as possible.
Overview The eGauge CT Extension Pack can be used to extend CT leads in situations where soldering or butt-splice connections...
November 11th, 2024 348 views 0 likes
Overview The most common installation issue with retrofit energy metering is known as a phase mismatch, which will cause incorrect...
November 11th, 2024 527 views 0 likes
Overview Use the guidance in this article to install and use your InHand IR302 cell modem. Prerequisites List any necessary...
November 14th, 2024 384 views 0 likes
Overview Follow the steps in this article to properly install split-core CTs for your eGauge. Prerequisites Caution! To reduce risk...
December 4th, 2024 437 views 0 likes
Overview This article covers the necessary steps and important information to consider when installing eGauge branded DC CTs with CTid....
December 9th, 2024 334 views 0 likes
Overview Follow the steps in this article to wire one or more serial devices to an EG4xxx model eGauge meter...
January 14th, 2025 407 views 0 likes
Overview Silicon solar irradiation sensors (Si sensors) offer an economical but robust and reliable solution for measuring solar irradiance levels,...
February 19th, 2025 383 views 0 likes
Overview By default, eGauge meters are set to obtain an IP address from a network via DHCP. If there is...
November 12th, 2024 710 views 0 likes
Overview This guide describes one method of installing the components in the 120V PEK. Remember that parts may be used...
January 21st, 2025 314 views 0 likes
January 21st, 2025 397 views 0 likes
Overview Follow the steps in this guide to register an eGauge meter to your eGauge.net portfolio. Prerequisites In order to...
January 13th, 2025 440 views 0 likes
Overview Follow the steps in this article to connect your EG42xx meter to an existing WiFi network. Prerequisites Important! eGauge...
January 20th, 2025 382 views 0 likes
Part 8: Verification Important step! After initial configuration it's important to verify readings and Important step! After initial configuration it's...
February 28th, 2025 438 views 0 likes
The powered enclosure kit (PEK) provides a collection of tested, supported hardware to make installing and mounting eGauge hardware. Additional...
February 27th, 2025 206 views 0 likes
Overview Follow the steps in this guide to install the eGauge Display Caster. Be sure to read the user manual...
March 27th, 2025 313 views 0 likes
Visit the online store page Model: ESH044 CTid The Sensor Hub and all related CTid enabled sensors are compatible...
October 28th, 2024 568 views 0 likes
Prerequisites: CTid The Sensor Hub and all related CTid enabled sensors are compatible with EG4xxx and newer and will not...
October 29th, 2024 343 views 0 likes
Overview The eGauge Pulse Sensor (EPS) connects directly to any EG4xxx series meter (Pro or Core) through a Sensor Hub,...
October 29th, 2024 451 views 0 likes
October 31st, 2024 341 views 0 likes
October 31st, 2024 312 views 0 likes
November 4th, 2024 293 views 0 likes
Overview The eGauge High Voltage sensor is used in conjunction with the Sensor Hub and an EG4xxx model meter (Core...
February 20th, 2025 389 views 0 likes
Prerequisites: eGauge meter with a minimum firmware version of v4.6.6 RS-485/USB converter Instructions: Step 1: For best results,...
March 5th, 2025 355 views 0 likes
Rope CTs should be installed properly to reduce the maximum error based on positioning. Ideally the conductor being monitored will...
March 31st, 2025 317 views 0 likes